Overview

With a 6’/1.83 m drum and a hopper that holds 6 cubic yards/4.6 cubic meters, the TR626 makes short work of processing material. Access the drum through removable side panels, drum end or top of the drum. Its 125 hp/93.2 kw John Deere 4045 Tier 4 Final is a powerful workhouse. Impressive 72.5’/22.1 m conveyor features self-cleaning tail pulley and return idlers.

Photos
Videos

TR626 with radial stacking conveyor | Vermeer Trommel Screens

Vermeer TR626 Tier 4i Trommel Screen - Organic Recycling Equipment

Features and Benefits

 

  • Enhance worker safety with startup delay and alarm systems that notify your whole crew when the machine is about to start.
  • Move material smoothly without bridging, thanks to a tall, wide throat opening.
  • Extend belt life even under tough loading conditions with closely set, heavy-duty rollers supporting the apron conveyor.  
  • Keep screen weights low when processing wet materials by clamping on a smaller diameter tension screen wire and increasing screening area.
  • Speed up your clean up because the flashing and sheeting fit tightly against the drum and conveyors to reduce spillage.
  • Forget the loading ramps, since the 626 has a low hopper infeed height.
  • See your Vermeer dealer for comprehensive service and genuine Vermeer replacement parts.
Specs
General Dimensions and Weights
Weight 49700 lbs 22543.5 kg
Hitch Weight 16680 lbs 7565.9 kg
Transport Length 54.5' 16.6 m
Transport Width 113" 287 cm
Transport Height 13.4' 4.1 m
Operation Length 84.4' 25.7 m
Operation Width 113" 287 cm
Operation Height 15.9' 4.8 m
Capacity Approximately 200 cu yd (152.9 cu m) per hour with .5" (1.3 cm) screens installed and material with moisture less than 40%   
Engine Option One
Make and Model John Deere PowerTech PVX 4.5L, 4045HFC93 Tier 4F
Number of Cylinders 4
Engine Rating 134 hp (93.2 kW) @ 2400 rpm, 398 ft-lb (531.6 Nm) of torque @ 1600 rpm
Fuel Tank Capacity 73 gal 276.3 L
Fuel Consumption 3.5 gph (13.3 L/hr) under most operating conditions
Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles) 30 deg
Battery 950 cold cranking amps
Oil Filter Spin-on
Recommended Oil Mobil 15/40
Oil Volume with Filter 15.5 qt 14.7 L
System Voltage 12 V, 120 amp alternator
Air Cleaner Dual element oversized
Radiator Fan Suction-type
Engine Option Two
Make and Model John Deere 4045H Tier 3
Number of Cylinders 4
Engine Rating 125 hp (93.2 kW) @ 2400 rpm, 355 ft-lb (481.3 Nm) of torque @ 1500 rpm
Fuel Tank Capacity 100 gal 378.5 L
Fuel Consumption 3.5 gph (13.3 L/hr) under most operating conditions
Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles) 30 deg
Battery 950 cold cranking amps
Oil Filter Spin-on
Oil Volume with Filter 15.5 qt 14.7 L
System Voltage 12 V, 120 amp alternator
Air Cleaner Dual element oversized
Radiator Fan Pusher type
Hydraulic System
Operation 62.9 gpm @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa])      
Tank capacity 200 gal 757.1 L
Chassis
Frame Description 4 independent hydraulic jacklegs
Axle/Suspension Leaf spring
Capacity 22500 lbs 10205.8 kg
Tires - Option One 235-75R 17.5H qty. 4
Hopper and Apron Conveyor
Hopper Capacity 6 cu yd 4.6 cu m
Hopper Bottom Width 48" 121.9 cm
Apron Conveyor Speed 0-205 fpm (0-62.5 m/min)
Apron Opening Height 34" 86.4 cm
Apron Opening Width 43" 109.2 cm
Hopper Height 9.5' (2.9 m) from ground level at operating incline
Hopper Opening 13.2' x 5.3' (4 m x 1.6 m)
Apron Conveyor Length 16' 4.9 m
Apron Conveyor Belt Width 48" 121.9 cm
Apron Conveyor Rollers 4" (10.2 cm) diameter qty. 14
Screen Drum
Drum Operation 0-42.6 gpm (161.3 L/min)
Drum Motor 48.8 cu in (800 cu cm) displacement
Drum Diameter 6' 1.8 m
Drum Support Description Four steel trunnion rollers 8 in (20.3 cm) diameter 4 in (10.2 cm) width
Thrust Bearing Diameter 5" 12.7 cm
Thrust Bearing Face 2.9" 7.4 cm
Drum Speed 0-21.6 rpm
Drum Drive Chain 140 WT
Drum Angle Adjustability 3-5 degrees
Maximum Screen Panels 8
Screen Brushes
Brush Diameter 14" 35.6 cm
Bristle Material Polyethylene
Brush Assembly Support Two 1.25" (3.2 cm) sealed ball bearings
Collecting Conveyor
Conveyor Motor Displacement 32.7 cu-in 535.9 cu-cm
Fines Belt Speed 405 ft/min 123.4 m/min
Conveyor Belt Width 36" 91.4 cm
Conveyor Belt Type 220 lb (99.8 kg), 2-ply, 2/16" x 1/16" (4.8 mm x 1.6 mm)   
Head/Tail Pulley Type Rubber-lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide   
Head Pulley Bearing 2.5" (6.4 cm) pillow block   
Rubber Flashing Adjustable, .25" (6.44 cm) thick, 4" (10.2 cm)   
Idler Type 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers   
Tail Pulley Takeup 12" 30.5 cm
Self-Cleaning Return Idlers 6, each 4" (10.2 cm) diameter   
Fines Conveyor Frame Part of trailer frame
Fines Conveyor
Conveyor Operation 15.4 gpm 58.3 L/min
Conveyor Motor Displacement 32.7 cu-in 535.9 cu-cm
Fines Conveyor Length 72.5' 22.1 m
Fines Belt Speed 405 ft/min 123.4 m/min
Conveyor Belt Width 36" 91.4 cm
Conveyor Belt Type 220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm)
Conveyor Belt Stacking Height 16.6' (5.1 m) with drum at 4 degrees
Head Pulley Type Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide
Head Pulley Bearing 2.5" (6.4 cm) pillow block
Rubber Flashing Adjustable, .25" (.64 cm) thick, 4" (10.16 cm)
Troughing Idler Type 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers
Self-Cleaning Tail Pulley Dimensions 10" (25.4 cm) diameter, 38" (96.5 cm) wide with 2.4" (6.1 cm) shaft
Tail Pulley Takeup 12" 30.5 cm
Self-Cleaning Return Idlers 11, each 4" (10.2 cm) diameter
Fines Conveyor Frame 4" x 8" (10.2 cm x 20.3 cm) structural steel tubing
Fines Conveyor Option-Radial
Conveyor Motor Displacement 15.9 cu-in 260.6 cu-cm
Fines Conveyor Length 30.5' 9.3 m
Fines Belt Speed 705 ft/min 214.9 m/min
Conveyor Belt Type 150 lb (99.8 kg), 2 ply, 1/32" x 1/32" (.8 mm x 0.8 mm), vulcanized
Head/Tail Pulley Type Rubber lagged, crowned, 9.75" (24.8 cm) diameter, 32" (81.3 cm) wide   
Head Pulley Bearing 2.5" (6.4 cm) pillow block   
Rubber Flashing Adjustable, .25" (6.4 mm) thick, 4" (10.2 cm)   
Idler Type 30 degrees CEMA "B" with permanently sealed bearings spaced at 41" (104 cm) centers   
Self-Cleaning Return Idlers 4, each 4" (10.2 cm) diameter   
Fines Conveyor Frame 2" x 8" (5.1 cm x 20.3 cm) structural steel building   
Overs Conveyor
Overs Conveyor Length 19' 5.8 m
Maximum Variable Overs Belt Speed 290 ft/min 88.4 m/min
Conveyor Belt Size 48" (121.9 cm) wide with raised crescent
Conveyor Belt Type 220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm)
Conveyor Belt Stacking Height 3' (.9 m) x 10' (3.1 m)
Head Pulley Type Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide
Head Pulley Bearing 2.5" (6.4 cm) pillow block
Self-Cleaning Tail Pulley Dimensions 10" (25.4 cm) diameter, 51" (129.5 cm) wide with 2.4" (6.1 cm) shaft
Tail Pulley Takeup 12" 30.5 cm
Solid Return Idler Size 4" x 8" diameter
Overs Conveyor Frame 4" x 8" (10.2 cm x 20.3 cm) structural steel tubing